342311 商业机械技工 Business Machine Mechanic

职业综述
州担保详情
ANZSCO代码和职业描述
职业类别

342311:商业机械技工 BUSINESS MACHINE MECHANIC SKILL LEVEL 3

MLTSSL	Medium and Long-term Strategic Skills List
STSOL	Short-term Skilled Occupation List
ROL	Regional Occupation List

GENERAL SKILLED VISA 189 无资格

Assessing Authority: TRA

State		Capital	Visa subclass 190	Visa subclass 491
ACT	Australian Capital Territory	Canberra	Yes	Yes
NSW	New South Wales	Sydney		Yes
NT	Northern Territory	Darwin	Yes	Yes
QLD	Queensland(Offshore list)	Brisbane
SA	South Australia	Adelaide	？	Yes
TAS	Tasmania (Category 1)	Hobart	Yes	Yes
VIC	Victoria	Melbourne		Yes
WA	Western Australia (General stream)	Perth

Yes：有资格Occupation may be Eligible

Yes：补充技术清单或特殊情况适用的职业 Occupation in the "Supplementary Skilled List" or "Special Conditions Apply"

Yes：职业不在"State Occupation List"或职业状态为“Closed”，但若满足条件仍有机会申请

？：点击州担保详情查看详情

ACCESS LIST
Status	State/Region	Type Visa	Explanation/Additional Requirements
Closed	New South Wales	Visa subclass 190
Open	New South Wales	Visa subclass 491 (regional)

ACCESS LIST
Status	Explanation
Closed	You may be eligible to apply for ACT nomination if you meet the nomination criteria.

ACCESS LIST
Status	English Requirements	Comments
Open	The applicant will be required to demonstrate a level of English either sufficient to meet licensing / registration or a minimum IELTS 6.0 score in each band, whichever is higher.

ACCESS LIST
Availability	Explanation	Additional Requirements
Open Low nomination	Low nomination places left	Competent English; Provisional 491 visa only - 190 nomination offered to applicants under specific circumstances only (see 3.5)

ACCESS LIST
Status	Important Information
Open

3423 电子行业技工

ANZSCO 3423 电子行业技工职责概述

• 维护、调整和修理电子设备、如商业和办公设备、视频和音频设备、电子仪器和控制系统、传输和接收广播信息。ELECTRONICS TRADES WORKERS maintain, adjust and repair electronic equipment such as commercial and office machines, video and audio equipment, and electronic instruments and control systems, and transmit and receive radio messages

ANZSCO 3423 电子行业技工技能要求 Indicative 技术等级 Skill Level
• 本单元的大多数职位需要具有与下述资质和经验相当的技术层次。Most occupations in this unit group have a level of skill commensurate with the qualifications and experience outlined below
• 在澳洲：AQF证书3级，包括至少2年的在职培训或AQF证书IV级（ANZSCO技术3级）In Australia: AQF Certificate III including at least two years of on-the-job training, or AQF Certificate IV (ANZSCO Skill Level 3)
• 在新西兰：NNZ资格证4级（ANZSCO技术3级）In New Zealand: NZ Register Level 4 qualification (ANZSCO Skill Level 3)
• 至少3年的工作经验可以代替上述的资格证。At least three years of relevant experience may substitute for the formal qualifications listed above.
• 有时除了资格证外，还需要相关的工作经验和/或在职培训。In some instances relevant experience and/or on-the-job training may be required in addition to the formal qualification
• 可能需要注册或许可。Registration or licensing may be required

ANZSCO 3423 电子行业技工主要职责 Tasks Include
• 检查并测试机器、设备、仪器和控制系统来确定故障。examining and testing machines, equipment, instruments and control systems to diagnose faults
• 调整、修理和更换磨损和残次部件，进行配线，维护机器、设备和仪器。adjusting, repairing, and replacing worn and defective parts and wiring, and maintaining machines, equipment and instruments
• 对设备重装、测试和调整。reassembling, test operating and adjusting equipment
• 告知用户正确的操作程序以防止发生故障。advising users of correct operating procedures to prevent malfunctions
• 接收代码，并将其转换为纯语言信息，书写和键入传输信息。receiving messages by interpreting code and converting to plain language, and writing and typing messages for transmission
• 监控无线电通信，传输和接受语音信息。monitoring radio traffic, and transmitting and receiving voice messages
• 安装电子仪器和控制系统。installing electronic instruments and control systems
• 应用电气、电子、机械、液压和气动原理方面的知识，试运行和维护控制系统。applying knowledge of electrical, electronic, mechanical, hydraulic and pneumatic principles in commissioning and maintaining control systems

NSW

ACT

NT

SA

TAS

342311 商业机械技工职业描述 Job description

342311 商业机械技工职位别名

342311 商业机械技工技术等级 Skill level

342311 商业机械技工所属职业列表

342311 商业机械技工澳洲技术移民职业评估 Skills assessment authority

相关职业